Operation of Model T-1

The How – To picture page of Castration for the Eze

This is a step by step process of loading the Castrator and the process of Castrating.
Please utilize our Question & Answer page also.

The Castrator Pictured is the Model T-1 Bloodless Castrator.

* Since these Pictures where taken, some modifications may have been made to the Model T-1. Although, some components may be somewhat different, the overall operation is the same.

1_warning_label_jpg
Warning Label
a_arm_pit_jpg
Place under arm pit.
aa_clip_in_castrator_jpg
Load clip w/ notch up and forward.
ac_clip_in_slot_jpg
Slide over pull rod
ad_clip_in_slot_inspection_jpg
May also pull the pull rod back so it is out of the way for easier installation.
ab_clip_slot__jpg
Place clip in slot so it is completely in and flush.
ae_clip_in_slot_inspection_jpg
Flush
b_band_spreader_bar_jpg
Hold band with thumb on top & index finger on end of spreader bar to keep from slipping off.
ba_band_spreader_bar_jpg
Continue holding while stretching band with other hand.
bb_band_spreader_bar_jpg
Stretch to other spreader bar and attach.
bc_band_spreader_bar_jpg
When stretching band, try to stretch the upper portion of the band as tight as possible, leaving the lower portion with as much slack as possible, since this will be the portion that will be stretched the most.
c_hold_band_both_thumbs_jpg
Hold band with both thumbs on top and both index fingers in the end of spreader bars.
d_pull_band_back_hook_jpg
Start stretching lower portion of band with remaining fingers.
da_pull_band_back_hook_jpg
Start stretching lower portion of band with remaining fingers.
db_pull_band_back_hook_jpg
Continue until band is in groove of pull back rod.
de_band_spreader_bar_jpg
Ensure band isn’t twisted when attaching to pull back rod.
e_preset_band_jpg
Hold castrator by the side grip handle. Side Grip may be removed and placed on other side if needed.
ea_preset_band_jpg
With other hand, pull the rod back until the band slips through the hole where you placed the clip.
eb_preset_band_jpg
Make sure the castrator is facing upright, since the clip may slip out of the slot.

ed_preset_band_jpg

ec_preset_band_jpg
Stop once the end of the rod lines up with the backside of the slot.
ee_preset_band_jpg
Castrator is fully loaded.
f_grip_scrotum_jpg
Firmly grip the scrotum and squeeze it a couple of times to work some of the fatty tissue downward. As if you were “Milking” a cow.
g_slip_band_on_scrotum_jpg
Continue holding the scrotum.
ga_slip_band_on_scrotum_jpg
Slip the scrotum through the band. Placing the band just above the testicles. DO NOT PLACE BAND NEXT TO THE BELLY. Just below it.
gb_slip_band_on_scrotum_jpg
Release the band from the castrator.
h_prep_to_tighten_jpg
To release band, continue holding scrotum with the same hand. Pull (jerk) the castrator back with the other hand. Don’t let the scrotum move while performing this.
ha_prep_to_tighten_jpg
Let the base of the castrator rest next to the scrotum and let the scrotum hang naturally. No need to pull back on the Castrator at this time.
i_tightening_band_jpg
Re-establish your grip on the Castrator. Place one hand on the side grip and one on the pull back rod.
ia_tightening_band_jpg
Pull back the rod as far as possible. While performing these steps, be careful NOT to hit the blade handle. Doing so will cut the band.
ib_tightening_band_jpg
Continue tightening with pistol grip handle.
j_crimping_jpg
There is a small stop weld on the pull back rod which will stop the rod from tightening any further.
ja_crimping_jpg
Use crimping handle to crimp aluminum retaining clip. Crimp until the handle stops.
k_cutting_band_jpg
Now use the blade handle to cut the band.

ka_cutting_band_jpg

kb_cutting_band_jpg
Top view of blade cutting band.
kc_cutting_band_jpg
Side view of blade cutting band.
kd_cutting_band_jpg
Follow through completely.
l_release_from_scrotum_jpg
Now “Jerk” back on the Castrator. And pull retaining clip from slot.
la_release_from_scrotum_jpg
Castrator completely removed from scrotum.
lb_band_on_scrotum_jpg
Inspect band to ensure no twists are present, and not to close to belly.
lc_band_on_scrotum_and_clip_jpg
Inspect clip to ensure it is on correctly.
m_retracting_pull_rod_jpg
Push pull back rod to original position. To do this, push and release the release switch located at the base of the pistol grip handle.

cr1  cr2 cr3